Q: What is the over all hieght that includes the gauge and body of the 4 body secondary regulator?
A: From the top of the gage to the barb is 8" in height
Q: Dumb question I know, but are these suitable for placement inside the kegerator / Keezer? Or are there any adverse effects in the colder 37F temperature?
No Answers have been submitted yet.
Q: If I add this to my primary regulator I am assuming all of the 4 secondarys must be set at or below the pressure on the primary regulator? If I am assuming correctly, the primary could be set at say 20lb, and each regulator could be set @ 10lb...
OR- does the primary have to be set higher to get enough pressure to all 4 secondarys? As in, maybe the primary has to be at or above the sum of all 4 secondary pressure settings? So if each secondary is set at 10lb....the primary would need to be set @ 40lb or higher?
A: the primary regulator would govern the pressure that feeds into the cerondary. If the primary is set at 3o psi, the max any of the gauges on the secondary can be set to, would be 30 as well. This can be don one all 4 bodys without needing the primary set at say 120psi to maintain 30 psi in each of the 4 bodies. the pressure in the primary can be set for 30, and the secondary bodies will balance out to 30 total once they are all turned to 30psi on the gauge
Q: Are these 0-60 psi regulators?
A: yes, each outlet feed is 0-60PSI
Q: The unit came shipped with the barb on the right and the stop on the left, can this be reversed? (I would like to have the barb on the left and the stop on the right.)
A: Yes, This should be able to be done without issue
Q: I need a 5 Body regulator, adding an extra Taprite Secondary Regulator (C384-T1661STC) with Taprite Hex Nipple 1/4" LHT x 1/4" LHT (c384-6618bl-2) will be enough? Also on the other end is this the gauge needed? Taprite 0-2000 Gauge (Taprite) (C384-6603-2000)? please let me know if something else is needed. Thanks
A: Yes, the parts you have listed would adapt this out to house an additional body. IF you prefer you can add the high pressure gauge to the end, but this is not mandatory and is a matter of preference.
Q: I have the "TapRite T-Handle Dual Gauge Regulator" (Item Number: c384-3741T) that came with AIH's "5 Gallon Ball Lock Keg System w/ Faucet and Shank, USED Keg (#3)" (Item Number: 99-3400) and additional "Keg Gas Line Assembly MFL" (Item Number: 99-GLBase) what else do I need to complete the build for this system?
No Answers have been submitted yet.
Q: What is the size of the barb? I'm ready to order but can't because don't know what size gas line and gas ball lock to get.
A: A standard 3/8 barb is used for gas.
Q: Will the 4 body secondary regulator require the single regulator still be attached to the C02 tank? Or can an adapter replace my single regulator with air lines running to the 4 body secondary regulator?
A: You still need a primary regulator coming from your tank.
Q: Can the barb shutoff valves be replaced with threaded connectors? Can it be ordered that way? The manifold I am replacing has threaded connections and hoses.
A: The shut offs can be changed, but you would need to do that yourself. We cannot modify the units, this would void the factory warranty.
Q: Which gauge would have the correct (LHT, RHT) to go on the left end of thev4 Body Secondary Regulator (Taprite) Item Number c384-T1694STC so that I have a tank regulator too?
A: The gauge would be RHT. You can use Item Number C384-6603-2000.
Q: What is the pressure range of each regulator?
A: Each gauge has a range from 0-60 psi.
Q: Do the shutoff valves contain check valves, or do I risk beer in the regulator?
A: The shutoffs all have check valves.
Q: When using these pressure regulators, does the pressure on the downstream unit have to be less than or equal to the upstream unit? For example if my primary regulator is discharging 20psi(carbing pressure) can I go (20 IN)->(8 out)->(12 out)->(8 out)->(20 out) ?
A: The gas pressure in any of the downstream regulators should not be restricted by the other regulators.
Q: How long are the 3 and 4 body regulators?
A: The three body secondary regulator is 11" long, the four body is 15" long.