Dip Tube & Carbonating Stone (Diffuser)

Diffuser Carbonating Stone Dip Tube

Send your review

Your Price: $66.99

Questions? Ask here.

Item Number: 91-3030

Availability: In stock

Quantity

67 points will be rewarded to you when you buy this item.

Description
Questions and Answers

Dip Tube & Carbonating Stone (Diffuser)

Works with stainless steel tanks to make a motorless carbonator. Assembly measures 21-7/8'' in length and has a an O.D. of 5/16''

NOTE: End must be flared after tank installation

Q: The instructions say the end must be flared after install. Does this use a compression fitting/ferrule to accomplish this task? If so what is the size needed? If not what is the correct method? Thanks very much! Regards, Jason

Asked by: Jason - 3/4/2020

A: This would require the use of a flaring tool, available at most well-stocked hardware stores. The tube can be left as-is and used with a 1/4" compression fitting to match the OD of the tubing used on the dip tube if preferred to lock it into place without the need for flaring the tube itself

Was this answer helpful? 0 of 0 Guest(s) found this Answer helpful.

Answer provided by: Aaron (3/5/2020)

Q: I have a 45 degree flaring tool, will this work? the old tube is flared 'flat'

Asked by: Greg Ogden - 3/9/2019

A: This could be used to flare the end of the tube on the carbstone

Was this answer helpful? 0 of 0 Guest(s) found this Answer helpful.

Answer provided by: Aaron (3/9/2019)

Q: Hi, I want to add one of these to a 5 gallon corny keg. How would I flare and fit this? Will I need other equipment to attach it? Thank you, David

Asked by: David - 8/16/2018

A: this can be attached or bridged to the inlet gas feed tube with a small piece of plexible tubing. Otherwise you would need a flaring tool to get the proper flare on the top of the tub if you intend to replce it with the exisiting tube on the inside of the keg

Was this answer helpful? 0 of 0 Guest(s) found this Answer helpful.

Answer provided by: Aaron (8/16/2018)

Q: After you use this to carb the beer, do you then serve through this as well? Does this cloudy the beer?

Asked by: Steven - 1/5/2018

A: This would be used on the gas inside dip tube and still served through the stnadardl iquid out tube on the keg.

Was this answer helpful? 0 of 0 Guest(s) found this Answer helpful.

Answer provided by: Aaron (1/5/2018)

Q: Is there a recommended PSI during use with this stone?

Asked by: Kemper Barkhurst - 4/19/2017

A: This will vary depending on how much co2 is needed for carbonating the liquid but anywhere from 5-30 psi is typical

Was this answer helpful? 1 of 2 Guest(s) found this Answer helpful.

Answer provided by: Aaron (4/19/2017)

Q: 3 questions: 1. Is the diffuser stone removable from the tube? 2. What micron is the stone? 3. Is it possible to get a longer dip tube?

Asked by: Justin Sights - 11/2/2014

A: The stone is not removable, and is a 5 micron stone. Unfortunately the dip tube only comes in one size, but it will work well with any 5 gallon cornelius style keg.

Was this answer helpful? 3 of 3 Guest(s) found this Answer helpful.

Answer provided by: Carson (11/3/2014)

Q: So does this just connect to the in post on your keg? And how does it actually connect?

Asked by: Brian - 10/16/2014

A: This dip tube is inserted up through the dip tube hole from inside the keg. You then will flare the top of the tube with a dip tube o-ring ( or two ) under the flare, and tighten your keg post on as usual.

Was this answer helpful? 4 of 5 Guest(s) found this Answer helpful.

Answer provided by: Carson (10/16/2014)

Q: Is this tube for corny kegs or is this for commercal keg?

Asked by: Timothy - 7/3/2014

A: This is meant for Cornelius kegs.

Was this answer helpful? 4 of 5 Guest(s) found this Answer helpful.

Answer provided by: Robert (7/3/2014)

Questions? Ask here.

CO2 Stem for CGA320 Valve LHT

$4.25

In stock

Select Options

Taprite Brass Hex Nipple 1/4" NPT x 1-1/2" long (RHT)

$3.99

In stock

(1)

Buy

Wing Nut, 29/32"-14 thread

$3.99

In stock

Buy

1/4" Commercial Tail Piece Assembly

$7.99

In stock

(2)

Buy

Go to Top of Page

Diffuser Carbonating Stone Dip Tube

Q: The instructions say the end must be flared after install. Does this use a compression fitting/ferrule to accomplish this task? If so what is the size needed? If not what is the correct method? Thanks very much! Regards, Jason

Q: I have a 45 degree flaring tool, will this work? the old tube is flared 'flat'

Q: Hi, I want to add one of these to a 5 gallon corny keg. How would I flare and fit this? Will I need other equipment to attach it? Thank you, David

Q: After you use this to carb the beer, do you then serve through this as well? Does this cloudy the beer?

Q: Is there a recommended PSI during use with this stone?

Q: 3 questions: 1. Is the diffuser stone removable from the tube? 2. What micron is the stone? 3. Is it possible to get a longer dip tube?

Q: So does this just connect to the in post on your keg? And how does it actually connect?

Q: Is this tube for corny kegs or is this for commercal keg?

Guests Also Bought...