Gas MFL Ball Lock Disconnect

5 Review(s) Send your review

Your Price: $7.08

Retail Price:$7.43

Your Savings:$0.35(5%)

Questions? Ask here.

Item Number: 60-2638

Availability: In stock

Click Box For 1/4 MFL Fitting

1/4 Swivel Flare nut x 3/8 barb for MFL disconnect [+$4.71]

Quantity	Price
3+	$6.87

Quantity

7 points will be rewarded to you when you buy this item.

Description
PRODUCT REVIEWS
Questions and Answers

Gas MFL Ball Lock Disconnect

Mfl threads are nice for quick changing lines or adding other equipment without cutting your lines.

Be sure to order the 1/4" or 3/8" female hose nipple with it!

Q: Hi, I ordered a Corny Key from you back in 2015 (Order 14-190583) and was starting to use it again today and I noticed that the ball-lock gas disconnects that I use without issues on two other kegs do not connect well to the keg I ordered from you. Any amount of pressure side-to-side (even the weight of the the gas line) will cause it to leak and I'm able to wiggle the disconnect quite a bit which also causes it to leak CO2. I've tested the same disconnect on my other kegs and it works fine without leaking or wiggling and I've tried 2 other disconnects on this keg with the same leaky results. I'm not sure what I could be doing wrong? Possibly the post's o-ring is bad, though it looks good and I've only used this keg once before? Or is there a different style disconnect that I should be using for this type of post and if so, what would that be? The ones I am using are similar to the threaded Gas MFL Ball Lock Disconnect (60-2638), but I'm not sure if there's a difference. Thanks! -Doug

Asked by: Douglas Cox - 6/3/2020

A: This issue is normally linked to a O'ring or gasket on the post that needs to be changed. If you have swapped it over and are still experiancing issues, we can be contacted via Email at [email protected] to work on getting this squared away. Thanks!

Was this answer helpful? 0 of 0 Guest(s) found this Answer helpful.

Answer provided by: Aaron (6/4/2020)

Q: I've purchased these from you before, and before ordering wanted to confirm that these are still CM Becker brand disconnects? Thanks

Asked by: Martin Black - 12/3/2018

A: The disconnects not being sold would be Shirron Brands and not CM Becker

Was this answer helpful? 0 of 1 Guest(s) found this Answer helpful.

Answer provided by: Aaron (12/3/2018)

Q: I'm confused about diameters. The Taprite regulator has a 5/16" barb but I believe this Gas MFL Ball Lock Disconnect has a 3/8" barb(?) Would 5/16" I.D. tubing fit both? Why does it recommend "Be sure to order the 1/4" or 3/8" female hose nipple with it"?

Asked by: John Smith - 11/12/2018

A: 5/16" ID is the common size for gas line tubing. The 3/8" barb just helps to give a more snug seal on that end of the tubing so it can be used on both a 3/8" and 5/16" barb without issues. Some brewers prefer to use the smaller 3/16" line for both their gas and beer so the recommendation to order the swivel just denotes that one or the other of a 1/4" swivel to 1/4" barb will be needed or a 1/4" swivel to 3/8" to complete the connection between the disconnects thread and the tubing

Was this answer helpful? 0 of 0 Guest(s) found this Answer helpful.

Answer provided by: Aaron (11/12/2018)

Q: Do these require an O ring?

Asked by: Cassandra Simpson - 4/18/2016

A: No, you will need a swivel barb.

Was this answer helpful? 0 of 0 Guest(s) found this Answer helpful.

Answer provided by: Desiree (4/22/2016)

Q: Do these require an o ring to seal properly?

Asked by: Cassandra Simpson - 4/11/2016

A: No it does not.

Was this answer helpful? 0 of 0 Guest(s) found this Answer helpful.

Answer provided by: Desiree (4/22/2016)

Q: Is this compatible with the blue plastic carbcap that you sell?

Asked by: Bill - 3/2/2016

A: Yes, it has the same diameter as the other white gas disconnect.

Was this answer helpful? 0 of 0 Guest(s) found this Answer helpful.

Answer provided by: Desiree (3/3/2016)

Q: What is the difference between this cm becker fitting and the other "white" one that you sell?

Asked by: David Crawford - 1/27/2015

A: These CM Becker disconnects are preferred by some brewers due to their reputation for quality. They cost a bit more to order, thus the small difference in price. We were continually asked to carry CM Becker disconnects, so we brought them in as an option.

Was this answer helpful? 4 of 4 Guest(s) found this Answer helpful.

Answer provided by: Carson (1/27/2015)

A: The other one is our brand. They are the same product just different brands.

Was this answer helpful? 0 of 0 Guest(s) found this Answer helpful.

Answer provided by: cortney (1/2/2016)

Questions? Ask here.

2 Keg Gas Line Assembly (ball or pin lock)

$18.89

In stock

(1)

Select Options

Keg Shank Line Assembly

$11.54

In stock

Select Options

Stainless Steel Gas Ball Lock Barbed Disconnect

~~$38.84~~ $31.49

In stock

Buy

Ball Lock Disconnect Set - MFL

$12.58

In stock

(8)

Select Options

Go to Top of Page

Gas MFL Ball Lock Disconnect

Quantity Pricing

Q: I've purchased these from you before, and before ordering wanted to confirm that these are still CM Becker brand disconnects? Thanks

Q: I'm confused about diameters. The Taprite regulator has a 5/16" barb but I believe this Gas MFL Ball Lock Disconnect has a 3/8" barb(?) Would 5/16" I.D. tubing fit both? Why does it recommend "Be sure to order the 1/4" or 3/8" female hose nipple with it"?

Q: Do these require an O ring?

Q: Do these require an o ring to seal properly?

Q: Is this compatible with the blue plastic carbcap that you sell?

Q: What is the difference between this cm becker fitting and the other "white" one that you sell?

Guests Also Bought...